電磁閥操作手冊翻譯-中英對照
操作過程
按 “執行”鍵畫面格式不變(如果凸輪或轉芯軸不在零位,機器會自動回到零位后,再等待)；搖手輪進行手動檢測或按“倍率”鍵作點動檢測。
D:按“自動”按鍵到自動開機畫面
①內容說明:
按“自動”按鍵模式切換成自動,機器按所編程序執行。
②操作過程
按“倍率”鍵搖手輪到所需要的適當速度。
E:按“編程修改”功能按鍵到修改畫面（不用停機修改程式）
①內容說明: 在機器自動運行中進入編程修改，畫面切換： 修改
②操作過程
按“F2”鍵不停機直接將光標移動到要修改的位置輸入要改的數據，按輸入鍵進行修改；全部修改完成后按執行鍵，機器在做完上一條彈簧后,執行修改后的程式,工作模式切換成“自動”。
F:按“程式目錄”功能按鍵到調用已有舊程式
詳細解釋請參照“按鍵說明”
G:按“I/O畫面”功能按鍵看輸入/輸出監控
詳細解釋請參照“按鍵說明”
H:按“參數設定”功能按鍵到相關設定參數
實例2 (畫面切換到用探針及用循環) Example 2 (picture switches to probe application and circulation)
N X1 X2 Y Yf D J L
1 50.0 120.0 50.00 1 3
2 135.3 154.0 -5.00
3 160.0 100.00 2.00 1 9
4 175.0 235.7 10.00 （-1）
5 257.1 289.5
說 明：(與實例1配合用)
1、 凸輪從50°轉至120°,同步送線50mm,轉芯到20°,循環從第1行開始，共將循環3次；
2、凸輪從135.3°轉至154°,同步退線5mm,轉芯到60°,在此處暫停0.5秒；
3、以默認轉速的80%,凸輪定位在160°，單步送線100mm,在送到98mm（Y-Yf）時, 電磁閥1打開，1號氣缸打出，探針命令有效，輔助送線2mm。 ①當探針探到時（探針碰到鋼線），電磁閥馬上關閉，汽缸馬上退回；②當探針沒有探到時（探針沒碰到鋼線），在送完Yf值（在此處是100 mm）的線后電磁閥自動關閉，汽缸退回；結束一個循環并返回第1行開始下一循環。在執行完3個循環（1>2>3> …1>2>3共3次）后，系統才開始執行第4行程式；
注解：①實際送線長度以碰到探針為準。 (不超過100 mm)
②送線到98mm時探針有效,開始減速（速度是參數設定畫面里的“探針?biāo)俣?rdquo;值），輔助送線碰探針, 碰到后即刻停止送線。(輔助送線值不超過2mm)
③在主畫面上必須設定“探針次數”探針才有效。(當“探針次數”設1次時，探針沒有碰到機器會馬上停，出現“探針失敗”提示而不出現報警；當“探針次數” 設2次或以上時,最后一條沒有碰到,機器要做完此條后才停，并且出現報警。)
4、凸輪從175 °轉至235.7°，同步送線10mm；
5、以默認轉速的180%,凸輪從257.1°轉至289.5°；
自動歸零后跳到第一行,再執行1—5行程序。
Comments: (cooperate with example1)
1. The cam is switched from 50°to 120°, the simultaneous feeding line is about 50mm, switch core to 20°, circulation begins from the 1st line, and it will circulate 3 times altogether;
2. The cam is switched from 135.3°to 154°, the simultaneous return line is about 5mm, switch core to 60°, suspend here for 0.5 seconds;
3. 80% of default rotational speed, the location of cam shall be reserved in 160°, the single-step line shall be 100mm, when the line sending is about to 98mm (Y-Yf ), the electromagnetic valve 1 is open, air cylinder No. 1 is open, the order of probe is effective, auxiliary feeding line is about 2mm .
① When the probe is reached (probe touches the copper wire), the electromagnetic valve shall be shut off at once, the cylinder shall be returned at once; ②When the probe was not reached (probe did not touch the copper wire ), the electromagnetic valve shall be closed automatically after finishing feeding the line of Yf value (100 mm herein ), the cylinder shall be returned; Finish a circulation and return the 1st lining; begin the next circulation. After finishing 3 circulation (1> 2> 3 of > to 1> 2> 3 all together in 3 times), the system shall begin the 4th procedure;
Note: ① The actual length of feeding shall subject to touch the probe. (not exceed 100 mm )
② The probe is effective while feeding line reach to 98mm, and begin to deceleration (speed is the " speed of the probe " value of set parameter in the picture ), when the feeding line of auxiliary touches the probe, it shall stop feeding the line instantaneously after touching. (the auxiliary value of feeding line shall not exceed 2mm)
③ It is valid when the " number of the probe times " set on the main picture. (when " number of the probe times "is set in the first time, the probe shall be stopped instantaneously if the probe has not reached the machine , " the probe will fail " shall be display with no alarm; When " number of the probe times " set for 2 times or above and did not touched , the machine shall shut down after finishing this procedure and alarm. )
4. the cam is switched from 175 °to 235.7°, the simultaneous feeding line is about 10mm;
5. 180% of default rotational speed, switch cam from 257.1°to 289.5°; jumping to the first line after automatic zero-set, carry out 1- 5 lines of procedures once again.
結合實例1和實例2在一起表述：
注意：該畫面是假想畫面并不真實存在
Combine the status of example1 and example 2:
Note: This picture is a hypothesis picture and does not exist really
N X1 X2 Y Z A Yf D F T J L
1 50.0 120.0 50.0 20.0 1 3
2 135.3 154.0 -5.0 60.0 5
3 160.0 100.0 120.0 2.0 1 80 9
4 175.0 235.7 10.0 130.0 (-1)
5 257.1 289.5 150.0 180
綜合表述：
1、凸輪從50°轉至120°,同步送線50mm,轉芯到20°,循環從第1行開始，共將循環3次；
2、凸輪從135.3°轉至154°,同步退線5mm,轉芯到60°,在此處暫停0.5秒；
3、以默認轉速的80%,凸輪定位在160°，同步送線98mm, 輔助送線2mm， 轉芯到120°,在送到98mm（Y-Yf）時, 電磁閥1打開，1號氣缸打出，探針命令生效，探針探到，氣缸自動退回，結束一個循環并返回第1行開始下一循環。在執行完3個循環（1>2>3> …1>2>3共3次）后，系統才開始執行第4行程式；
４、凸輪從175°轉至235.7，同步送線10mm，轉芯到130°；
5、以默認轉速的180%,凸輪從257.1°轉至289.5°，不送線,轉芯到150°；
自動歸零后跳到第一行,再執行1—5行程序。
Comprehensive statement:
1. The cam is switched from 50°to 120°, the simultaneous feeding line is about 50mm, circulation begins from the 1st line, and it will circulate 3 times altogether;
2. The cam is switched from 135.3°to 154°, the simultaneous return line is about 5mm, switch core to 60°, suspend here for 0.5 seconds;
3. 80% of default rotational speed, the location of cam shall be reserved in 160°, the simultaneous line shall be 98mm, the auxiliary feeding line is about 2mm. when the feeding line is about to 98mm (Y-Yf ), the electromagnetic valve 1 is open, air cylinder No. 1 is open, the order of probe is effective, the cylinder shall be returned automatically at once; Finish a circulation and return the 1st lining; begin the next circulation. After finishing 3 circulation (1> 2> 3 of > to 1> 2> 3 all together in 3 times), the system shall begin the 4th procedure;
4. the cam is switched from 175 °to 235.7°, the simultaneous feeding line is about 10mm;
5. 180% of default rotational speed, switch cam from 257.1°to 289.5°; jumping to the first line after automatic zero-set, carry out 1- 5 lines of procedures once again.
2013.1.15