反應性標準測試方法翻譯-中英對照
骨料組合潛性堿質反應性標準測試方法 (灰漿棒方法) 1
本標準按照標號C 227制定; 在修正情況下，標號后表明原先采納的年度或，先前修正的年度。括號內數字表明上次重新評價的年度。上標ε (e)表明最后修正或重新評價編輯變化。
本標準經國防部的代辦處批準使用。
1. 范圍
1.1本測試方法用于在測試規定的情況下，通過測量存貯期間組合包含灰漿棒增量(或減退的)的長度，確定關于氫氧離子與堿的膨脹反應 (鈉和鉀)骨料組合的極化率。
1.2參加膨脹反應的堿通常從水泥中獲得; 在某些情況下，他們也可以從外部來源獲得或從混凝土的其它組成部分中獲得�？梢源_認聚集體堿反應性的二個類型：(1) 硅質巖石、礦物和自然或人造玻璃與堿硅土反應 (2) 某些方解石白云巖中的白云巖和含白云石的石灰石的堿碳酸鹽反應(參見標準C294)。不推薦該方法作為探測后者反應的手段，因為在灰漿棒測試堿碳酸鹽反應導致的擴張 (參見測試方法C 586)比堿硅土反應生產的一般要少，組合在使用中有同等的惡性影響。
1.3在SI中陳述的數值視為標準數值。括號內顯示的非SI數值只作提供的參考信息。
1.4本標準不表述所有相關安全陳述，如果有，陳述只與用途相關。本標準的用戶有責任建立適當?shù)陌踩l(wèi)生實踐，并且在使用之前確定適當?shù)陌踩A(yù)防措施。
2. 參考文件
2.1 ASTM標準：
C 33混凝土骨料規格
C 109/C 109M水凝水泥灰漿耐壓強度測試方法(使用2英寸.或[50毫米]立方體
標本) 3
C 289潛性堿硅土反應性測試方法
C 294混凝土骨料2聚集體(化工方法) 2標準描寫命名原則
C 295混凝土骨料2巖石分類測試指南
C 305機械混合的水凝水泥漿體和砂漿的塑性稠度實施規范
C 490使用器具硬化水泥漿的漿體，砂漿和混凝土的長度變動實施規范
C 511用于水凝水泥和混凝土2,3測試的濕治室、濕氣室和儲水箱規格
C 586混凝土骨料2碳酸鹽巖石潛性堿反應性測試方法(圓柱形巖石測試方法)
C 856硬化混凝土2巖相學測試實施規范
C 1437確定水凝水泥漿體3流程測試方法
E 11篩布和篩子測試目的4規格
3. 意義和用途
3.1在混凝土實施中，使用該方法執行混凝土骨料組合測試結果數據，以及巖相學測試的結果(指南C 295)，以及出版的骨料潛性反應性化工方法測試方法C 289測試的結果和結果數據，應該根據關于混凝土材料中的混凝土骨料組合的結論和建議，咨詢相關使用該測試方法的測試結果。
1本實施規范符合混凝土和混凝土骨料ASTM委員會C09規定，并由C09.26材料化學反應小組委員會直接負責。
當前版本于2003年6月10日批準。出版日期2003年9月。1950年最初批準。前早版本C 227 – 97于1997批準。
ASTM標準2年鑒書，第04.02卷。
ASTM標準3年鑒書，第04.01卷。
ASTM標準4年鑒書，第14.02卷。
復制權© ASTM國際， 100 Barr港口驅動， PO箱子C700，西部Conshohocken， PA 19428-2959，美國。
ASTM國際版權
經過ASTM批準由IHS提供
未經HIS允許，不允許復制或網絡轉載
Standard Specification for
Lightweight Aggregates for Structural Concrete1
This standard is issued under the fixed designation C 330; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1, This specification covers lightweight aggregates in¬tended for use in structural concrete in which prime consider¬ations are reducing the density while maintaining the compres-sive strength of the concrete. Procedures covered in this specification are not intended for job control of concrete.
1.2 The values stated in SI units are to be regarded as the
standard. The values shown in parentheses are for information
purposes only.
1.2.1 With regard to other units of measure, the values stated in inch-pound units are to be regarded as standard.
1.3 The text of this standard references notes and footnotes
which provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered
as requirements of the standard.
NOTE 1—This specification is regarded as adequate to ensure satisfac¬tory lightweight aggregates for most concrete. It is recognized that it may be either more or less restrictive than needed for some conditions and for special purposes, such as fire resistance, fill, and concrete constructions, the use of which is based on load tests rather than conventional design procedures.
2. Referenced Documents
2.1 ASTM Standards: 2
C 29/C 29M Test Method for Bulk Density ("Unit Weight") and Voids in Aggregate
C 31/C 31M Practice for Making and Curing Concrete Test Specimens in the Field
C 33 Specification for Concrete Aggregates
C 39/C 39M Test Method for Compressive Strength of Cy¬lindrical Concrete Specimens
C 40 Test Method for Organic Impurities in Fine Aggre¬gates for Concrete
C 114 Test Methods for Chemical Analysis of Hydraulic Cement
1 This specification is under the jurisdiction of ASTM Committee C09 on
Concrete and Concrete Aggregates and is the direct responsibility of Subcommittee
C09.21 on Lightweight Aggregates and Concrete.
Current edition approved Jan. 1, 2004. Published February 2004. Originally approved in 1953. Last previous edition approved in 2003 as C 330 — 03a.
2 For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard's Document Summary page on
the ASTM website.
C 136 Test Method for Sieve Analysis of Fine and Coarse Aggregates
C 142 Test Method for Clay Lumps and Friable Particles in Aggregates
C 151 Test Method for Autoclave Expansion of Portland Cement
C 157/C 157M Test Method for Length Change of Hard¬ened Hydraulic-Cement, Mortar, and Concrete
C 192/C 192M Practice for Making and Curing Concrete Test Specimens in the Laboratory
C 496 Test Method for Splitting Tensile Strength of Cylin¬drical Concrete Specimens
C 567 Test Method for Determining Density of Structural Lightweight Concrete
C 641 Test Method for Staining Materials in Lightweight Concrete Aggregates
C 666 Test Method for Resistance of Concrete to Rapid Freezing and Thawing
C 702 Practice for Reducing Samples of Aggregate to Testing Size
D 75 Practice for Sampling Aggregates
2.2 ACI Standards:
ACI 211.2 Standard Practices for Selecting Proportions for Structural Lightweight Concrete 3
3. Aggregate Types
3.1 Two general types of lightweight aggregates are covered
by this specification, as follows:
3.1.1 Aggregates prepared by expanding, pelletizing, or
sintering products such as blast-furnace slag, clay, diatomite,
fly ash, shale, or slate, and
3.1.2 Aggregates prepared by processing natural materials,
such as pumice, scoria, or tuff.
3.2 The aggregates shall be composed predominately of
lightweight-cellular and granular inorganic material.
4. Chemical Composition
4.1 Lightweight aggregates shall not contain excessive amounts of deleterious substances, as determined by the following limits:
3 Available from American Concrete Institute, PO Box 9094, Farmington Hills, MI 48333.
copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
Copyright ASTM International
Reproduced by IHS under license with ASTM
No reproduction or networking permitted without license from IHS
Not for Resale
C 330 - 04
4.1.1 Organic Impurities (Test Method C 40)—Lightweight
aggregates that, upon being subjected to test for organic
impurities, produce a color darker than the standard shall be
rejected, unless it is demonstrated that the discoloration is due
to small quantities of materials not harmful to the concrete.
4.1.2 Staining (Test Method C 641)—An aggregate produc¬
ing a stain index of 60 or higher shall be rejected when the
deposited stain is found upon chemical analysis to contain an
iron content, expressed as Fe2O3 equal to or greater than 1.5
mg/200 g of sample.
2013.2.12