保溫箱內部設定說明-中英對照
1支撐、托盤和支架必須必須保持干凈，不得有任何肥皂沫或70%酒精的成分，
2如圖1所示，將右側的內壁移到到右上部。然后按照箭頭（1）標明的方向：將底部按照箭頭（2）標明的方向推擠到右下側。
3然后，如圖2所示，將左側的內壁移到左上部，然后按照箭頭（3）標明的方向：將底部按照箭頭（4）標明的方向推擠到左下側。
圖1 圖2
4.將通風孔托盤移到里面，輕輕地掀動，然后按照圖3的說明，放在箱內的上側。用帶有保溫箱的自帶的螺絲安裝通風孔托盤。在通風孔托盤的每邊和內壁上設有通風孔(參見圖4)；
圖3 圖4
安裝托架
1.首先，按照圖5所示，在孔洞的狹縫處安裝支架。將支架勾在孔洞上，然后將支架推入狹縫內。
2第二步，按照圖7所示，將托架的另一個末端勾在孔洞上（離門較近那個)。
3如上述，將托架設置在右邊和左邊您想要按照托架和支架的位置。并且將支架推入
確定支架保持水平。(參見圖8)
圖5圖6
4用蒸餾水甚至理想的水，倒在箱（室）底部的不銹鋼托盤，大約托盤70%位置即可，進行增濕(參見圖9)。
圖9
保持保溫箱清潔。保證每周換水一次，或采用更頻繁的周期。
請注意:如果自來水含鐵，會造成箱（室）內生銹；
增濕
水對增濕而言是非常重要的，可以影響到清潔度和濕度。每天檢查一次到二次確保保水質清潔和新鮮。并且每周換水一次。建議使用純凈水或蒸餾水；
建議定期換水，使用純凈水或蒸餾水，為方便增濕，可以將水溫加熱到37.0°C，
注：如果保溫箱斷電后使用時間超過30分鐘，確保將烘干箱中的水倒出，并完全干燥，然后關閉電源。
注：如果保溫箱斷電后使用時間超過30分鐘，確保烘干箱完全干燥，然后關閉電源。
在供電或斷電時，烘干箱（室）必須保持干燥。否則會造成二氧化碳探測器無效和發生故障。
連接二氧化碳?xì)怏w
1連接附上的塑料軟管到氣體入口。
2連接軟管的其它終端到氣體壓力調節裝置。
3二氧化碳供氣選擇壓力為0-03 Mpa
4在引入二氧化碳?xì)怏w之前入箱（室）確保溫度和濕氣穩定。
CO2 GAS Connect Port氣體連接口
Calibrated GAS Connect Port校準氣體連接口岸
Back of 保溫箱: 保溫箱背后
注： 二氧化碳?xì)怏w的供應壓力是大于0.03Mpa，會造成所有探測器甚而所有管材發生故障和破裂。
保溫箱通電
在墻壁上的電源輸出口插上AC電纜。然后，起動保溫箱上部右邊的電源開關；
接通電源時，保溫箱上的溫度顯示和二氧化碳閃動幾秒鐘。
然后，保溫箱繼續控制溫度和二氧化碳?xì)怏w保持在現有值水平；
Power Switch:電源開關
Right side view:右邊視圖
設定方式
執行設定方式：按下并且按住“設置”按鍵十秒鐘，溫度顯示，然后交替顯示當前溫度和 “設置”字樣；
當保溫箱第一次使用時需要用到設定模式，當保溫箱設置在這個模式時，保溫箱不引入二氧化碳?xì)怏w并且控制二氧化碳?xì)怏w和在下一個12小時內某些警報，在這個12個小時內沒有引入任何二氧化碳?xì)怏w，保溫箱在穩定的溫度和濕氣條件下運行。在溫度和濕氣穩定之后。保溫箱開始引入二氧化碳?xì)怏w入箱內；
在設定方式期間，如果保溫箱斷電，設定方式將自動地取消。
注: 確保安置相當數量水在保溫箱的底部。如果沒有一定數量的水，二氧化碳探測器不能探測和控制實際二氧化碳?xì)怏w正確密度。
Chamber Interiors Set-up
1, Shelve, Tray and brakets MUST be Cleaned with either inveted soap or 70% ethanol,
2 Slide the right inner-wall into the upper right-hand side comer as shown in the figure 1. towards the direction that arrow indicated with ) then: push the bottom part of the wall into the direction that arrow indicates as lower right-hand side.
3, Then, Slide the left inner-wall to the upper left-hand side corner as shown in the figure 2, towards the direction that arrow indicated with 1), then, push the bottom part of the wall into the direction that arrow (*indicates as lower left-hand side.
Figure 1 Figure 2
4, Bring in the Air Vent Tray to the inside, slightly tilted then put it up to the inner-top as shonwn in
the Figure 3. Install the Air Vent Tray with the screws that are provided with the incubator.
There are holes on each side of the Air Vent Tray and the top of inner-walls for installation
(See Fighre 4),
Figure3
Figure 4
Installing Brackets
1, First, Set a barcket to the hole with a slit as Figure 5 shows. Hook on the bracket to the hole and push the bracket into the slit as Fighre shows.
2
. Then, hook the the other end of the bracket to the hole the one closer to the door). Hook it on tight as Figure 7 shows.
3
_ Set the Brackets to both right and left hand-side as stated above to the positions where you want the brackets and shoes. And slide the shelves in
Make sure the Shelves are hoiizontally EVEN. (See Fighre
8)
Figure 5 Figure 6
4, Fill in the Stainless Steel Tray with Distilled water or even better water, about 70% up to the tray and place it on the bottom on the chamber for humidification (See Figure 9).
To Keep Me incubator clean. Make sure to change the Water for Humidification every once in a week or mole frequently.
Please Note that If tap-water that contains iron content. it would cause for the inner Chanmber to get ranted
Humidification
The Water for Humidification is a very important factor that would influence the cleanliness and, off course, Humidity. Make sure to keep the water clean and fresh by checking the water about everyday or two. And change the water in about every once a week. Pure water or Distilled water is recommended to use as
Regular water change is recommended to use the Pure water i Distilled water that are warm up to around 37.0'C, for even quicker humidity regain
Note: If the incubator is to be left powered off for more than 30 minutes, Make sure to remove the water completely and dry the chamber thoroghly, then turn the power off.
A Note: When the incubator is to be used after being powered off for more than 30 minutes, Make sure that the chamber is completely dried up. Then, turn the power on.
The Chamber MUST be dried, when Powered ON or OFF. It would cause the C02 Sensor to be failed and malfunctioned.
Connecting C02 GAS
1, Connect the attached plastic hose to the Port for each GAS.
2, Connect the other ends of the hose to GAS pressure regulators.
3, The Optimal pressure of C02 GAS supply is 0-03 Mpa
4, Make sure that the Temperature and humidity are stabilized before introducing C02 GAS into the Chamber.
02 GAS Connect Port
akibrated GAS Connect Port o f
Back of IncubatorNote: lithe Supply pressure of C02 GAS is too greater than 0.03Mpa, it would cause to all the sensors to malfunction, and even all the tubing to burst.
Power up the Incubator
Plug the AC cable to the wall power outlet. Then, turn on the power switch that is on the Upper Right side of the Incubator_
When Powered on, Temp. Display and 002 Display will brink for a several seconds.
Then, the incubator proceeds to control the temperature and C02 GAS for the preset Value_
. Power Switch
Right Side View
SET-UP MODE
To execute the Set-up mode: press and hold the "SET" key for more than 10 seconds_ Temperature Display, then displays the present temperature and word "SET" reciprocally
The Set-up mode is to be used when first set-up the incubator_ When the incubator is set to
this mode, the incubator is programed not to introduce and control the 002 GAS and some of the Alarms for the next 12 hours, During this 12 hours of no 002 GAS being introduced, the incubator operates to stabilize the temperature and humidity. After the temperature and humidity are stabilized. the incubator starts to inject the C02 GAS into the chamber_
If the incubator is powered off during the Set-up mode, the Set-up mode will be automatically cancelled.
2013.2.7